OPERATING MODE
| DMX Control | DMX mode, receive DMX signal, RDM signal |
| Auto Run | Fixture run automatically according to built-in programs |
| Sound Control | When the fixture detects a strong sound, the fixture automatically runs a scene according to the built-in program, otherwise it will stay the last scene |
| Scene Mode 01 | runs in a set scebe, which supports most of the custom editing of 10 scenes. |
| 1~10 | outputs the specified scene |
| Auto | Automatically loops the output scene in the set scene time (non-zero) order, and the scene with time 0 automatically ignore |
| M/S Choose | Master and slave selection, non-DMX mode takes effect, select the mode of data output, fixture detect DMX cable state automatic switch output, prevent data conflicts |
| Master | Fixture runs built-in program. If DMX has no signal, it outputs data (synchronization), otherwise it does not output data. |
| Slave | Fixture runs built-in program and do not output data |
| Auto | If DMX has no signal, the fxiture will runs built-in program. Otherwise, the fixture will run in DMX Mode(follow DMX). |
| Lamp Switch | (Lamp light source) pop-up confirmation dialog box, select "SURE" to confirm the current operation, turn on or off the lamp, switch time interval limited to 30 seconds |
| Off | The current lamp output is off |
| On | The current lamp output is turned on |
DISPLAY SETTING
| Language | Display language settings |
| English | English display |
| Chinese | Chinese display |
| Screen Saver | Set screen 30 seconds without operation, the screen's display content or method. |
| OFF | Keep the last operation page |
| Mode1 | Black |
| Mode2 | Black screen, showing the address code of the current fixture in the lower left corner. |
| Mode3 | Display trademark information, address code and operation mode. |
| Screen Rot | Set the display direction of the screen. |
| OFF | No reverse display |
| ON | Reverse display |
| DMX Indicate | Set the indication mode of DMX signal indicator. |
| Mode1 | When signal is bright, no signal is off. |
| Mode2 | When signal is off, no signal is bright. |
| Mode3 | When signal is flash, no signal is off. |
| Screen Light | Set the screen backlight for 10 seconds without operation |
| 1~10 | 10 |
Instalaltion Struction:
CABLE CONNECTION DMX
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24AWG, low capacity. Do not use microphone cable or other cable withcharacteristics differing from those specified. Theendconnections must be made using XLR type3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4W)between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
RIGGING(OPTIONAL)
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.
Operation Instructions -The moving head is for beam wash spot purpose. -Don't turn on the fixture if it's been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature. -This light should be keep away from strong shaking during any transportation or movement. -Don't pull up the light by only the head, or it might cause damages to the mechanical parts. -Don't expose the fixture in overheat, moisture or environment with too much dust when installing it. And don't lay any power cables on the floor. Or it might cause electronic shock to the people. -Make sure the installation place is in good safety condition before installing the fixture. Sub Menu(Parameter) 
If you use a controller with a 5 pin DMX output connector. You will need to use a 5pin to 3 pin as apter
Model No: DMX5M. Or DMX 5F The chart below details a proper cable conversion: 
Parameter value setting
When the selected item is value need to been modified, the dialog shown in Figure 4 will popup.
Installation Instructions
Light fixtures can be placed horizontally, slanted, and hung upside down.Be sure to pay attention to the installation method when hanging diagonally and upside down.
As shown in Figure 2, before positioning the lamp, it is necessary to ensure the stability of the installation site. When installing the reverse hanging, it is necessary to ensure that the lamp does not fall down on the support frame. It is necessary to use the safety rope through the support frame and the lamp handle for auxiliary hanging to ensure safety. Prevent the luminaire from falling and sliding.
When installing and debugging the lamps, it is forbidden for pedestrians to pass under them. Regularly check whether the safety rope is worn and whether the hook screws are loose.
Our company does not assume any responsibility for all consequences caused by the fall of the lamp due to the unstable installation of the hanging.
Schematic diagram of the lamp hanging upside down
Stage moving head lights are widely used in stage performances and performances. Here are some of their application scenarios:
Stage shows: Stage moving headlights are widely used for concerts, theatrical performances, dance performances and other stage shows. They can create a variety of lighting effects for the stage by moving, rotating and adjusting the Angle of the beam, enhancing visual impact and artistic expression.
Concerts and music festivals: In large concerts and music festivals, stage moving headlights are used to illuminate artists, bands and various parts of the stage. They can enhance the visual effects of musical performances by creating a variety of dynamics and atmospheres through color changes, beam effects and movement.
Theatre and stage plays: In theatre and stage plays, stage moving headlights are used to illuminate actors, stage sets and props. They can create different lighting scenes that highlight the emotion and drama of the performance through changes in light and projection effects.
Events and exhibitions: Stage mobile headlights are also widely used in various events and exhibitions, such as corporate events, product launches and art exhibitions. They can create memorable visuals for the scene, capture the audience's attention and enhance the atmosphere of the event.
Film and television production: In film and television production, stage moving headlights are used to illuminate sound stages, set scenes, and highlight actors. They can create lighting effects suitable for different scenes and plots through various lighting effects and dynamic changes.
Flexible, programmable and versatile, stage mobile head lamps can be precisely controlled and adjusted according to specific needs. They provide a rich variety of lighting effects for stage performances and performances, helping to create a memorable visual experience.
1.From the date of purchase, the product is provided with a free warranty for 5 years, and the following conditions are not included in the free warranty during the warranty period:
Failure and damage caused by unpacking products;
Failure caused by falling and touching during handling and use;
Failure to operate in accordance with the instructions.
2.After the warranty period, if the parts need to be replaced during the maintenance process, only the cost of materials to replace the parts, free of time costs.
FAQ:
Q1: Are you a manufacturer?
MF: Yes, we are a manufacturer with our own factory. We have over 14 years of experience in research and development, as well as manufacturing, and we operate based on ISO quality management since 2009.
Q2: Can I order a sample of the LED Tri-proof Light?
MF: Yes, we welcome sample orders to test and check the quality of our products. Mixed samples are also acceptable.
Q3: What is the lead time for the LED Tri-proof Light?
MF: For sample orders, the lead time is 3-7 days, and for mass production orders, it is 15-25 days. The exact lead time depends on the order quantities.
Q4: How do you ship the finished products?
MF: We offer optional shipping methods such as by SEA, AIR, or Express (DHL, UPS, FedEx, TNT, etc.).
Q5: Can I print my logo on the LED Tri-proof Light?
MF: Yes, we provide OEM service to our customers. We can help to make the label and color box according to your requirements.
Q6: How do I proceed with an order for the LED Tri-proof Light?
MF: Firstly, please let us know your detailed requirements and application environment. Secondly, we will recommend some suitable products and solutions to you based on your request. Thirdly, after confirming all the details, customers will issue a purchase order and make the payment to confirm, and then we will start production and arrange shipment.
Q7: How do you handle defective products?
MF: All of our products are produced in strict quality control systems, and the defective rate is less than 0.2% according to our shipment records. We offer a 5-year warranty for this product. If there is any defect during the warranty period, please provide pictures or videos of the defective lights in working situations, and we will ship new lights to you within a few days or together with your next order.
